USE_TXENABLE 16F1783 timeout

[petspats]

Hey!

Thank you for the great software.
It works great:

Initiating write...
Searching for bl . . . . . . .
Found PIC16F1783 fw ver. 1.0.2
Waiting for the boot loader to be ready...ok
Hex file successfully parsed
Writing flash....ok
Tx 387 bytes / Rx 14 bytes / 4,4s
Write successfully completed

However when i enable USE_TXENABLE it will just time out:

Initiating write...
Searching for bl . .
Found PIC16F1783 fw ver. 1.0.2
Waiting for the boot loader to be ready...ok
Hex file successfully parsed
Writing flash....response timed out
Write flash failed
Tx 8 bytes / Rx 4 bytes / 30,9s
Write failed

So how could i fix this?

Hoping for help.
Peeter

[Mikael Gustavsson]

Hi Peter,
Why do you want to use a tx enable pin if it works without?

[petspats]

Hey Mikael!

I want to implement it for RS485. That is the reason.

Thank you for fast answer!

[petspats]

Hey again.

I think i was misleading abit.
I am using bootloader over UART to USB and it is working. Now since i plan to use it with UART to RS485 to USB i was testing out this tx enable pin. I am stil using UART to USB and i am just hoping to watch the tx enable pin on oscilloscope. But as you can see if i enable this option it will not get contact anymore.

I hope it is clearer now

Thanks!
Peeter

[petspats]

[miklosch]

Hello!

I have a same problem with PIC18F26K22.
I use RS485 line, and I can not write flash.
Error is:
Initiating write...
     Searching for bl . . . . . .
     Found PIC18F26K22 fw ver. 3.0.2
     Waiting for the boot loader to be ready...ok
     Hex file successfully parsed
     Writing flash.... response timeout
     Writing flash...
     Write flash failed
     Tx 164 bytes / Rx 9 bytes / 3s
     Write failed
Or:
Initiating write...
     Searching for bl .
     Found PIC18F26K22 fw ver. 3.0.2
     Waiting for the boot loader to be ready...ok
     Hex file successfully parsed
     Writing flash....unknown response 0xFF
     Writing flash...
     Write flash failed
     Tx 159 bytes / Rx 9 bytes / 0,5s
     Write failed

But I can write the eeprom with same config:
Initiating write...
     Searching for bl . . . . . .
     Found PIC18F26K22 fw ver. 3.0.2
     Waiting for the boot loader to be ready...ok
     Hex file successfully parsed
     Writing eeprom...ok
     Tx 454 bytes / Rx 68 bytes / 3,8s
     Write successfully completed

It work without RS485 perfectly:
Initiating write...
     Searching for bl .
     Found PIC18F26K22 fw ver. 3.0.2
     Waiting for the boot loader to be ready...ok
     Hex file successfully parsed
     Writing flash....ok
     Writing eeprom...ok
     Tx 3,9kB / Rx 160 bytes / 5,6s
     Write successfully completed

[petspats]

[miklosch]

I measured the communication with scop. I attached the pictures. Red is a TX line, and yellow is an RX line from PC.
EEPROM write working fine in both communication (RS232, RS485). FLASH writhe working only with RS232.
I think, in flash write mode answare the PIC too fast. TXE_DELAY number has no effect.
Attachment:
1: RS485 flash write
2: RS485 flash write enlarged
3: RS232 flash write
4: RS485 eeprom write
5: RS485 eeprom write enlarged

[Mikael Gustavsson]

Hi,
Thank you petspats for the report. I was able to reproduce the problem and fix it with your path. The problem is that the RCSTA register may be located in a different memory bank than the tx enable pin port register. I will publish a new version of the ds30 Loader free edition package when I get time.

miklosch: please start a separate thread.