2015-11-24, 07:26:58
(This post was last modified: 2015-11-24, 07:57:38 by raye.
Edit Reason: Added project files
)
Hi All,
I am getting the following output error when i build the project in MPLAB v8.89.
Here is my setting.inc file
Here is my user code file.
Any help would be real appreciated :-)
Thanks
Ray
I am getting the following output error when i build the project in MPLAB v8.89.
Code:
----------------------------------------------------------------------
Release build of project `C:\ds30_Loader_140817\ds30 Loader\firmware_PIC12F_PIC16F\ds30Loader.mcp' started.
Language tool versions: MPASMWIN.exe v5.48, mplink.exe v4.46, mplib.exe v4.46
Tue Nov 24 13:12:55 2015
----------------------------------------------------------------------
Clean: Deleting intermediary and output files.
Clean: Done.
Executing: "C:\Program Files (x86)\Microchip\MPASM Suite\MPASMWIN.exe" /q /p16F1455 "ds30loader.asm" /l"ds30loader.lst" /e"ds30loader.err"
Error[113] C:\DS30_LOADER_140817\DS30 LOADER\FIRMWARE_PIC12F_PIC16F\SRC\UART.INC 116 : Symbol not previously defined (SPBRG)
Error[113] C:\DS30_LOADER_140817\DS30 LOADER\FIRMWARE_PIC12F_PIC16F\SRC\UART.INC 118 : Symbol not previously defined (SPBRG)
Halting build on first failure as requested.
----------------------------------------------------------------------
Release build of project `C:\ds30_Loader_140817\ds30 Loader\firmware_PIC12F_PIC16F\ds30Loader.mcp' failed.
Language tool versions: MPASMWIN.exe v5.48, mplink.exe v4.46, mplib.exe v4.46
Tue Nov 24 13:12:56 2015
----------------------------------------------------------------------
BUILD FAILEDHere is my setting.inc file
Code:
;------------------------------------------------------------------------------
;
; Title: ds30 Loader for PIC12F and PIC16F
;
; File description: user settings and configuration bits
;
; Copyright: Copyright 2010-2012 Mikael Gustafsson
;
;------------------------------------------------------------------------------
;------------------------------------------------------------------------------
; This file is part of ds30 Loader.
;
; ds30 Loader is free software: you can redistribute it and/or modify
; it under the terms of the GNU General Public License as published by
; the Free Software Foundation.
;
; ds30 Loader is distributed in the hope that it will be useful,
; but WITHOUT ANY WARRANTY; without even the implied warranty of
; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
; GNU General Public License for more details.
;
; You should have received a copy of the GNU General Public License
; along with ds30 Loader. If not, see <http://www.gnu.org/licenses/>.
;------------------------------------------------------------------------------
;------------------------------------------------------------------------------
; Device
;------------------------------------------------------------------------------
;LIST P=16F1938
LIST P=16F1455
;------------------------------------------------------------------------------
; Includes
;------------------------------------------------------------------------------
#include "devices.inc"
;------------------------------------------------------------------------------
; User preferences
;------------------------------------------------------------------------------
radix DEC
#define FOSC 4000000 ;xxx
#define BLINIT 2000 ;xxx hello receive timeout [ms]
#define HELLOTRIES 2 ;xxx number of non hello characters received before branching to the user application
#define BLTIME 2000 ;xxx data receive timeout [ms]
;------------------------------------------------------------------------------
; UART settings
;------------------------------------------------------------------------------
#define USE_UART1 1 ;xxx uncomment to use uart1
;#define USE_UART2 1 ;xxx uncomment to use uart2
#define BAUDRATE 19200 ;xxx baudrate
;#define USE_ABAUD 1 ;xxx auto baud rate detection, only available on enhanced mid-range devices(?)
#define USE_BRGH 0 ;xxx
#define USE_BRG16 0 ;xxx 16-bit brg, only available on enhanced mid-range devices(?)
;#define USE_TXENABLE 1 ;xxx uncomment to use a tx enable pin
#ifdef USE_TXENABLE
#define TXE_DELAY 10 ;xxx time in us to wait before transmitting after pulling the tx enable pin high
#define TRISR_TXE TRISB ;xxx tris register containing tx enable
#define PORTR_TXE PORTB ;xxx port register containing tx enable
#define TRISB_TXE TRISB0 ;xxx tris bit for tx enable
#define PORTB_TXE RB0 ;xxx port bit for tx enable
#endif
;------------------------------------------------------------------------------
; Advanced settings
;------------------------------------------------------------------------------
;#define KICK_WD 1 ;xxx uncomment if the watchdog is enabled
#define WRITE_VER 1 ;xxx do flash write verification
#define EWRITE_VER 0 ;xxx do eeprom write verification
#define BLPLW 256 ;bootloader placement, words from end, should be a multiple of 64
;------------------------------------------------------------------------------
; Configuration bits, these macros can be found at the end of the inc-files located in
; C:\Program Files\Microchip\MPASM Suite\
;
; These can also be set in MPLAB IDE instead, they are found in Configure->Configuration bits...
;------------------------------------------------------------------------------
; Template for standard PIC16F, usually two-three letter like PIC16F88 or PIC16F877
;__CONFIG _CONFIG1, _DEBUG_OFF &_HS_OSC & _WDT_OFF & _PWRTE_OFF & _MCLR_ON & _BODEN_OFF & _LVP_OFF
;__CONFIG _CONFIG2, _IESO_OFF & _FCMEN_OFF
; Template for enhanced PIC16F, usually four letter like PIC16F1936
__CONFIG _CONFIG1, _FOSC_INTOSC & _WDTE_OFF & _PWRTE_OFF & _MCLRE_ON & _CP_OFF & _BOREN_ON & _CLKOUTEN_OFF & _IESO_OFF & _FCMEN_OFF
__CONFIG _CONFIG2, _WRT_OFF & _CPUDIV_NOCLKDIV & _PLLEN_DISABLED & _STVREN_ON & _LVP_OFF
;------------------------------------------------------------------------------
; ds30 Loader commercial version
;------------------------------------------------------------------------------
;-Supports read of flash and EEPROM
;-Supports software UART
;-Read more at www.ds30loader.com
;------------------------------------------------------------------------------
; End of file
;------------------------------------------------------------------------------Here is my user code file.
Code:
;------------------------------------------------------------------------------
;
; Title: ds30 Loader for PIC12F and PIC16F
;
; File description: user init and exit code
;
; Copyright: Copyright © 2011, Mikael Gustafsson
;
;------------------------------------------------------------------------------
;------------------------------------------------------------------------------
; This file is part of ds30 Loader.
;
; ds30 Loader is free software: you can redistribute it and/or modify
; it under the terms of the GNU General Public License as published by
; the Free Software Foundation.
;
; ds30 Loader is distributed in the hope that it will be useful,
; but WITHOUT ANY WARRANTY; without even the implied warranty of
; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
; GNU General Public License for more details.
;
; You should have received a copy of the GNU General Public License
; along with ds30 Loader. If not, see <http://www.gnu.org/licenses/>.
;------------------------------------------------------------------------------
;------------------------------------------------------------------------------
; UserInit()
; Description: this is executed immediately on start-up before the boot loader code
;------------------------------------------------------------------------------
UserInit macro
ifndef DEV_MODE
; Set internal oscillator to 8MHz
;banksel OSCCON
;bsf OSCCON, IRCF0 ;bank 1
;bsf OSCCON, IRCF1
;bsf OSCCON, IRCF2
; Make uart pins digital
ifdef ANSEL
;error Do you need to configura uart pins to be digital? If not, remove this line
;banksel ANSEL
endif
ifdef ANSELA
;error Do you need to configura uart pins to be digital? If not, remove this line
BANKSEL PORTA ;
CLRF PORTA ;Init PORTA
BANKSEL LATA ;Data Latch
CLRF LATA ;
BANKSEL ANSELA ;
CLRF ANSELA ;digital I/O
BANKSEL TRISA ;
MOVLW B'00000000' ;Set as outputs
MOVWF TRISA ;and set
endif
ifdef ANSELC
;error Do you need to configura uart pins to be digital? If not, remove this line
BANKSEL PORTC ;
CLRF PORTC ;Init PORTC
BANKSEL LATC ;Data Latch
CLRF LATC ;
BANKSEL ANSELC ;
CLRF ANSELC ;digital I/O
BANKSEL TRISC ;
MOVLW B'00000000' ;Set as outputs
MOVWF TRISC ;and set
endif
endif ;DEV_MODE
endm
;------------------------------------------------------------------------------
; UserExit()
; Description: this is executed right before the user application is loadaed
;------------------------------------------------------------------------------
UserExit macro
endm
;------------------------------------------------------------------------------
; End of file
;------------------------------------------------------------------------------Any help would be real appreciated :-)
Thanks
Ray
