2013-08-16, 11:04:02
(This post was last modified: 2013-08-21, 21:24:29 by Mikael Gustavsson.)
Hi all:
Thanks Milael for this free piece of work!It is amazing!
I have tried to access the ds30 to my dsPIC33FJ16GS504 board.But i can not write flash correctly.Each time i tried to connect GUI to my Board ,i always received such erro informations:
i think my PPS config is alright,my C code is showed below and i changed it to asm
Thanks Milael for this free piece of work!It is amazing!
I have tried to access the ds30 to my dsPIC33FJ16GS504 board.But i can not write flash correctly.Each time i tried to connect GUI to my Board ,i always received such erro informations:
Quote:Initiating write...my setting file is showed below
Creating port: USB-SERIAL CH340 (COM11)
Opening port USB-SERIAL CH340 (COM11)@256000
Searching for bl . (discarded null byte) (discarded null byte) (discarded null byte) (discarded null byte) (discarded null byte) (discarded null byte) (discarded null byte) timed out
Closing port
Tx 20 bytes / Rx 160 bytes / 10s
Write failed
Code:
;------------------------------------------------------------------------------
; Device
;------------------------------------------------------------------------------
;.equ __24F16KA102, 1 ;xxx uncomment and change if using PIC24F device
;.equ __24FJ128GA010, 1 ;xxx uncomment and change if using PIC24FJ device
;.equ __24HJ128GP504, 1 ;xxx uncomment and change if using PIC24HJ device
;.equ __30F4011, 1 ;xxx uncomment and change if using dsPIC30F device
;.equ __33FJ256GP710, 1 ;xxx uncomment and change if using dsPIC33FJ device
;.equ __33FJ128MC802, 1 ;
.equ __33FJ16GS504, 1
;------------------------------------------------------------------------------
; Includes
;------------------------------------------------------------------------------
.include "devices.inc"
;------------------------------------------------------------------------------
; User preferences
;------------------------------------------------------------------------------
.equiv FCY, 40000000 ;xxx speed of internal cycle clock[Hz], used to calculate uart brg and delay
.equiv BLINIT, 3000 ;xxx hello receive timeout [ms] 3000
.equiv HELLOTRIES, 2 ;xxx number of non hello characters received before branching to the user application
.equiv BLTIME, 3000 ;xxx data receive timeout [ms]
;------------------------------------------------------------------------------
; UART settings
;------------------------------------------------------------------------------
.equiv USE_UART1, 1 ;xxx uncomment to use uart1
;.equiv USE_UART2, 1 ;xxx uncomment to use uart2
;.equiv USE_UART3, 1 ;xxx uncomment to use uart3
;.equiv USE_UART4, 1 ;xxx uncomment to use uart4
;.equ USE_ALTIO, 1 ;xxx uncomment to use uart 1 alternative i/o, only for dsPIC30F
.equiv BAUDRATE, 19200 ;xxx baudrate 115200
;.equiv USE_ABAUD, 1 ;xxx uncomment to use auto baud rate detection, READ ERRATA FIRST
;.equiv USE_BRGH, 1 ;xxx uncomment to use high baud rates, READ ERRATA FIRST, not available for PIC24F
;.equiv USE_TXENABLE, 1 ;xxx uncomment to use a tx enable pin
.ifdef USE_TXENABLE
.equiv TRISR_TXE, TRISA ;xxx tris register containing tx enable
.equiv LATR_TXE, LATA ;xxx port register containing tx enable
.equiv TRISB_TXE, TRISA1 ;xxx tris bit for tx enable
.equiv LATB_TXE, RA1 ;xxx port bit for tx enable
.endif
;------------------------------------------------------------------------------
; CAN settings, commercial version only www.ds30loader.com
;------------------------------------------------------------------------------
;------------------------------------------------------------------------------
; Security, commercial version only www.ds30loader.com
;------------------------------------------------------------------------------
;------------------------------------------------------------------------------
; Advanced settings
;------------------------------------------------------------------------------
.equiv PROT_GOTO, 1 ;protect goto at 0x00
.equiv PROT_BL, 1 ;protect bootloader
.ifdef IS_24F
.ifndef USE_SECURE
.equiv BLPLP, 6 ;bootloader placement, pages from end
.equiv BLSIZEP, 6 ;bootloader size [pages], used by bootloader protection
.else
.equiv BLPLP, 27 ;bootloader placement, pages from end
.equiv BLSIZEP, 27 ;bootloader size [pages], used by bootloader protection
.endif
.endif
.ifdef IS_24FJ
.ifndef USE_SECURE
.equiv BLPLP, 2 ;bootloader placement, pages from end
.equiv BLSIZEP, 1 ;bootloader size [pages], used by bootloader protection
.else
.equiv BLPLP, 2 ;bootloader placement, pages from end
.equiv BLSIZEP, 2 ;bootloader size [pages], used by bootloader protection
.endif
.endif
.ifdef IS_24HJ
.ifndef USE_SECURE
.equiv BLPLP, 1 ;bootloader placement, pages from end
.equiv BLSIZEP, 1 ;bootloader size [pages], used by bootloader protection
.else
.equiv BLPLP, 2 ;bootloader placement, pages from end
.equiv BLSIZEP, 2 ;bootloader size [pages], used by bootloader protection
.endif
.endif
.ifdef IS_30F
.ifndef USE_SECURE
.equiv BLPLP, 8 ;bootloader placement, pages from end
.equiv BLSIZEP, 8 ;bootloader size [pages], used by bootloader protection
.else
.equiv BLPLP, 27 ;bootloader placement, pages from end
.equiv BLSIZEP, 27 ;bootloader size [pages], used by bootloader protection
.endif
.endif
.ifdef IS_33FJ
.ifndef USE_SECURE
.equiv BLPLP, 1 ;bootloader placement, pages from end
.equiv BLSIZEP, 1 ;bootloader size [pages], used by bootloader protection
.else
.equiv BLPLP, 2 ;bootloader placement, pages from end
.equiv BLSIZEP, 2 ;bootloader size [pages], used by bootloader protection
.endif
.endif
;------------------------------------------------------------------------------
; Configuration bits, these macros can be found at the end of the inc-files located in
; c:\Program files\Microchip\MPLAB ASM30 Suite\Support\dsPIC33F\inc
;
; These can also be set in MPLAB IDE instead, they are found in Configure->Configuration bits...
;------------------------------------------------------------------------------
.ifdef IS_24F
;config __FBS, BSS_OFF/*Boot Segment Code Protect*/ & BWRP_OFF/*Boot Segment Write Protect Enable*/
;config __FGS, GCP_OFF/*General Segment Code Protect*/ & GWRP_OFF/*General Segment Write Protect Enable*/
config __FOSCSEL, FNOSC_FRC/*Initial Oscillator Select*/ & IESO_OFF/*Two Speed Start-up*/
config __FOSC, FCKSM_CSDCMD/*Clock switching and Fail-Safe Clock monitor*/ & SOSCSEL_SOSCLP/*Secondary Oscillator Select*/ & POSCFREQ_MS/*Primary Oscillator Frequency Range*/ & OSCIOFNC_ON/*OSCO Pin Configuration*/ & POSCMOD_XT/*Oscillator Selection*/
;config __FWDT, FWDTEN_OFF/*Watchdog Timer*/ & WINDIS_OFF/*Windowed WDT*/ & FWPSA_PR32/*Watchdog prescaler*/ & WDTPS_PS1/*Watchdog postscale*/
;config __FPOR, MCLRE_ON/*Master Clear Enable*/ & BORV_LPBOR/*Brown Out Voltage*/ & I2C1SEL_PRI/*I2C1 pins Select*/ & PWRTEN_OFF/*Power Up Timer*/ & BOREN_BOR0/*Brown Out Reset*/
;config __FICD, BKBUG_OFF/*Background Debugger*/ & ICS_PGx1/*ICD pins select*/
;config __FDS, DSWDTEN_OFF/*Deep Sleep Watchdog Timer*/ & DSBOREN_OFF/*Deep Sleep BOR*/ & RTCOSC_LPRC/*RTCC Reference Oscillator Select*/ & DSWDTOSC_LPRC/*Deep Sleep Watchdog Oscillator Clock Select*/ & DSWDTPS_DSWDTPS0/*Deep Sleep Watchdog Postscale*/
.endif
.ifdef IS_24FJ
config __CONFIG1, JTAGEN_OFF/*JTAG*/ & GCP_OFF/*code protect*/ & GWRP_OFF/*write protect*/ & BKBUG_OFF/*background debugger*/ & COE_OFF/*clip-on emulation mode*/ & ICS_PGx2/*icd pins select*/ & FWDTEN_OFF/*watchdog timer*/ & WINDIS_OFF/*windowed wdt*/ & FWPSA_PR32/*watchdog prescalar*/ & WDTPS_PS1/*watchdog postscalar*/
config __CONFIG2, IESO_OFF/*two-speed startup*/ & FNOSC_FRC/*oscillator selection*/ & FCKSM_CSDCMD/*clock switching and clock monitor*/ & OSCIOFNC_OFF/*OSC0/RC15 function*/ & POSCMOD_XT/*oscillator selection*/
;config __CONFIG3, WPEND_WPSTARTMEM/*write protect range selection*/ & WPCFG_WPCFGDIS/*write protection config page*/ & WPDIS_WPEN/*write protection*/ & WPFP_WPFP8/*Write Protection Flash Page*/
.endif
.ifdef IS_24HJ
;config __FBS, RBS_NO_RAM & BSS_NO_FLASH & BWRP_WRPROTECT_OFF ;xxx boot segment
;config __FSS, RSS_NO_RAM & SSS_NO_FLASH & SWRP_WRPROTECT_OFF ;xxx secure segment
;config __FGS, GSS_OFF & GCP_OFF & GWRP_OFF ;xxx general segment
config __FOSCSEL, FNOSC_FRC & IESO_OFF ;xxx oscillator mode
config __FOSC, FCKSM_CSDCMD & OSCIOFNC_ON & POSCMD_XT ;xxx clock switching/clock monitor, osc2 & oscillator selection
;config __FWDT, FWDTEN_OFF & WINDIS_OFF ;xxx watchdog
;config __FPOR, FPWRT_PWR1 ;xxx pwm, power-on reset
;config __FICD, BKBUG_ON & COE_ON & JTAGEN_OFF & ICS_PGD1
.endif
.ifdef IS_30F
config __FOSC, CSW_FSCM_OFF & FRC_PLL16 ;xxx oscillator
config __FWDT, WDT_OFF ;xxx watchdog
config __FBORPOR, PBOR_OFF & RST_IOPIN & PWRT_OFF & MCLR_EN ;xxx power-on reset, brown-out reset, master clear
;config __FGS, CODE_PROT_OFF & GWRP_OFF ;xxx code protection
config __FICD, ICS_PGD ;xxx comm channel select
.endif
.ifdef IS_33FJ
;config __FBS, RBS_NO_RAM & BSS_NO_FLASH & BWRP_WRPROTECT_OFF ;xxx boot segment
;config __FSS, RSS_NO_RAM & SSS_NO_FLASH & SWRP_WRPROTECT_OFF ;xxx secure segment
;config __FGS, GSS_OFF & GCP_OFF & GWRP_OFF ;xxx general segment
;** FNOSC_PRI Primary oscillator (XT, HS, EC)
;** FNOSC_PRIPLL Primary oscillator (XT, HS, EC) w/ PLL
; Two-speed Oscillator Startup :
; IESO_OFF Disabled
; IESO_ON Enabled
;#define IESO_OFF 0xFF7F
;#define IESO_ON 0xFFFF
; config __FBS, RBS_NO_RAM & BSS_NO_FLASH & BWRP_WRPROTECT_OFF ;xxx boot segment
; config __FSS, RSS_NO_RAM & SSS_NO_FLASH & SWRP_WRPROTECT_OFF ;xxx secure segment
; config __FGS, GSS_OFF & GCP_OFF & GWRP_OFF ;xxx general segment
config __FOSCSEL, FNOSC_PRIPLL & IESO_OFF ;xxx oscillator mode
config __FOSC, FCKSM_CSECMD & OSCIOFNC_ON & POSCMD_XT ;xxx clock switching/clock monitor, osc2 & oscillator selection
config __FWDT, WDTPOST_PS256 & WDTPRE_PR128 & FWDTEN_OFF & WINDIS_OFF ;xxx watchdog
config __FPOR, FPWRT_PWR1 ;xxx pwm, power-on reset
;config __FICD, JTAGEN_OFF & ICS_PGD1 ;xxx
;xxx
.endifi think my PPS config is alright,my C code is showed below and i changed it to asm
Code:
RPINR18bits.U1RXR = 20; //??rp20(2o???)?????aU1RX
RPOR10bits.RP21R = 3; //??rp21(3o???)?????aU1TX
