2010-12-28, 15:02:58
(This post was last modified: 2024-07-04, 20:56:21 by Mikael Gustavsson.)
Hello,
I am trying to run the bootloader on a 18F2520 @ 20Mhz.
I have changed the settings.inc file (see below) and programed the .hex with my WISP628.
When i want to connect with the PIC i run the DS30loader GUI, press on the "check for bl" and reset the pic by pulling the MCLR low. But after 10 seconds i can see : seraching fot bl ................... time out
what do i wrong?
I am trying to run the bootloader on a 18F2520 @ 20Mhz.
I have changed the settings.inc file (see below) and programed the .hex with my WISP628.
When i want to connect with the PIC i run the DS30loader GUI, press on the "check for bl" and reset the pic by pulling the MCLR low. But after 10 seconds i can see : seraching fot bl ................... time out
what do i wrong?
Quote:;------------------------------------------------------------------------------
;
; Title: ds30 Loader for PIC18F
;
; File description: user settings and configuration bits
;
; Copyright: Copyright © 09-10, Mikael Gustafsson
;
; History: 2.0.3 Renamed fosc to oscf
; 2.0.2 New setting: NODENR
; New setting: NODENR_BL
; New setting: PROT_GOTO
; New setting: PROT_BL
; 2.0.1 New setting: HELLORETRIES
; 2.0.0 CAN support
; 1.0.2 -
; 1.0.1 -
; 1.0.0 Added BLINIT
; 0.9.2 Added tx enable support
; 0.9.1 -
; 0.9.0 first version of this file
;
;------------------------------------------------------------------------------
;------------------------------------------------------------------------------
; This file is part of ds30 Loader.
;
; ds30 Loader is free software: you can redistribute it and/or modify
; it under the terms of the GNU General Public License as published by
; the Free Software Foundation.
;
; ds30 Loader is distributed in the hope that it will be useful,
; but WITHOUT ANY WARRANTY; without even the implied warranty of
; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
; GNU General Public License for more details.
;
; You should have received a copy of the GNU General Public License
; along with ds30 Loader. If not, see <http://www.gnu.org/licenses/>.
;------------------------------------------------------------------------------
;------------------------------------------------------------------------------
; Device
;------------------------------------------------------------------------------
LIST P=18F2520; ;xxx
;------------------------------------------------------------------------------
; Includes
;------------------------------------------------------------------------------
#include "devices.inc"
;------------------------------------------------------------------------------
; User preferences
;------------------------------------------------------------------------------
radix DEC
#define OSCF 20000000 ;xxx oscillator frequency
#define BAUDRATE 9600 ;xxx baudrate
#define BLTIME 2000 ;xxx data receive timeout [ms]
#define BLINIT 2000 ;xxx hello receive timeout [ms]
#define HELLOTRIES 2 ;xxx number of non hello characters received before branching to the user application
#define USE_UART1 1 ;xxx uncomment to use uart1
;#define USE_UART2 1 ;xxx uncomment to use uart2
;#define USE_CAN ;xxx uncomment to use CAN instead of UART
;#define USE_TXENABLE 1 ;xxx uncomment to use a tx enable pin
#ifdef USE_TXENABLE
#define TRISR_TXE TRISC ;xxx tris register containing tx enable
#define LATR_TXE LATC ;xxx port register containing tx enable
#define TRISB_TXE TRISC6 ;xxx tris bit for tx enable
#define LATB_TXE RC6 ;xxx port bit for tx enable
#endif
;------------------------------------------------------------------------------
; CAN settings
;------------------------------------------------------------------------------
#define ID_PIC 1 ;xxx node number for this device
#define ID_GUI 0x7ff ;xxx node number of the ds30 Loader gui
;------------------------------------------------------------------------------
; Advanced settings
;------------------------------------------------------------------------------
#define PROT_GOTO 1 ;xxx protect goto at 0x00
#define PROT_BL 1 ;xxx protect bootloader
#define BLPLP 7 ;bootloader placement, pages from end
#define BLSIZEP 7 ;bootloader size [pages], used by bootloader protection
;------------------------------------------------------------------------------
; Configuration bits, these macros can be found at the end of the inc-files located in
; C:\Program Files\Microchip\MPASM Suite\
;
; These can also be set in MPLAB IDE instead, they are found in Configure->Configuration bits...
;------------------------------------------------------------------------------
;config OSC = INTIO2 ;internal oscillator
;config FSCM = OFF ;failsafe clock monitor
;config IESO = OFF ;internal external switchover mode
;config PWRT = OFF ;power-up timer
;config BOR = OFF ;brown-out reset
;config BORV = 27 ;brown-out reset value
;config WDT = OFF ;watchdog timer
;config WDTPS = 1 ;1:1 WDT prescalar
;config MCLRE = ON ;MCLR
;config STVR = ON ;stack overflow reset
;config LVP = OFF ;low voltage programming
;config DEBUG = OFF ;debug
;config CP0 = OFF ;
;config CP1 = OFF ;
;config CPB = OFF ;
;config CPD = OFF ;
;config WRT0 = OFF ;
;config WRT1 = OFF ;
;config WRTB = OFF ;
;config WRTC = OFF ;
;config WRTD = OFF ;
;config EBTR0 = OFF ;
;config EBTR1 = OFF ;
;config EBTRB = OFF ;
;__CONFIG _CONFIG1L, _PLLDIV_5_1L & _CPUDIV_OSC3_PLL4_1L & _USBDIV_2_1L
;__CONFIG _CONFIG1H, _FOSC_HSPLL_HS_1H & _FCMEM_OFF_1H & _IESO_OFF_1H
;__CONFIG _CONFIG2L, _PWRT_ON_2L & _BOR_OFF_2L ; _VREGEN_OFF_2L
;__CONFIG _CONFIG2H, _WDT_OFF_2H & _WDTPS_1_2H
;__CONFIG _CONFIG3H, _MCLRE_ON_3H & _PBADEN_OFF_3H & _CCP2MX_OFF_3H
;__CONFIG _CONFIG4L, _DEBUG_OFF_4L & _LVP_OFF_4L & _STVREN_OFF_4L & _XINST_OFF_4L
;__CONFIG _CONFIG5L, _CP0_OFF_5L & _CP1_OFF_5L & _CP2_OFF_5L
;__CONFIG _CONFIG5H, _CPB_OFF_5H & _CPD_OFF_5H
;__CONFIG _CONFIG6L, _WRT0_OFF_6L & _WRT1_OFF_6L & _WRT2_OFF_6L & _WRT3_OFF_6L
;__CONFIG _CONFIG6H, _WRTB_OFF_6H & _WRTC_OFF_6H & _WRTD_OFF_6H
;__CONFIG _CONFIG7L, _EBTR0_OFF_7L & _EBTR1_OFF_7L & _EBTR2_OFF_7L & _EBTR3_OFF_7L
;__CONFIG _CONFIG7H, _EBTRB_OFF_7H
