2017-12-03, 12:52:15
Hi, I'm trying to use Ds30 Loader (v 1.5.7-2.2.14) with PIC24FJ256GB210, but I can not write in the Flash.
I receive the following error:
-------------------------------------------------------------------------------------
Initiating write...
Searching for BL.
Found PIC24FJ256GB210 FW ver. 4.0.3
Waiting for the boot loader to be ready... ok
Hex file successfully parsed
Writing Flash.... verification error (1), trying again...
Writing Flash... verification error (2), trying again...
Writing Flash... Write Failed
Write Flash failed
Tx 601 Bytes/Rx 8 bytes/0, 5s
Write failed
-------------------------------------------------------------------------------------
Baud: 57600
Config:
Config _ _ CONFIG1, JTAGEN_OFF/* JTAG */& GCP_OFF/* Code protect */& GWRP_OFF/* Write protect */& ICS_PGX2/* ICD Pins SELECT */& FWDTEN_OFF/* Watchdog timer */& WINDIS_OFF/* Windowed WDT */& ALTVREF_ALTVREDIS &/* Alternate VREF location Enable-< < < GB210 Only >> > */& FWPSA_PR128/* watchdog */& WDTPS_PS32768/* watchdog */
Config _ _ CONFIG2, IESO_OFF/* Two-speed startup */& PLLDIV_NODIV &/* 96 MHz PLL prescaler Select */& FNOSC_FRCPLL/* Oscillator selection */& FCKSM_CSDCMD/* clock switching and clock monitor */& OSCIOFNC_ON/* OSC0/RC15 function */& IOL1WAY_OFF &/* IOLOCK One-Way Set Enable */& POSCMOD_NONE/* Oscillator selection */
Config _ _ CONFIG3, WPEND_WPENDMEM/* Write protect Range selection */& WPCFG_WPCFGDIS/* Write protection Config page */& WPDIS_WPDIS/* Write protection */& WPFP_WPFP255/* Write Protection Flash page */
What can be the problem?
Thank you.
I receive the following error:
-------------------------------------------------------------------------------------
Initiating write...
Searching for BL.
Found PIC24FJ256GB210 FW ver. 4.0.3
Waiting for the boot loader to be ready... ok
Hex file successfully parsed
Writing Flash.... verification error (1), trying again...
Writing Flash... verification error (2), trying again...
Writing Flash... Write Failed
Write Flash failed
Tx 601 Bytes/Rx 8 bytes/0, 5s
Write failed
-------------------------------------------------------------------------------------
Baud: 57600
Config:
Config _ _ CONFIG1, JTAGEN_OFF/* JTAG */& GCP_OFF/* Code protect */& GWRP_OFF/* Write protect */& ICS_PGX2/* ICD Pins SELECT */& FWDTEN_OFF/* Watchdog timer */& WINDIS_OFF/* Windowed WDT */& ALTVREF_ALTVREDIS &/* Alternate VREF location Enable-< < < GB210 Only >> > */& FWPSA_PR128/* watchdog */& WDTPS_PS32768/* watchdog */
Config _ _ CONFIG2, IESO_OFF/* Two-speed startup */& PLLDIV_NODIV &/* 96 MHz PLL prescaler Select */& FNOSC_FRCPLL/* Oscillator selection */& FCKSM_CSDCMD/* clock switching and clock monitor */& OSCIOFNC_ON/* OSC0/RC15 function */& IOL1WAY_OFF &/* IOLOCK One-Way Set Enable */& POSCMOD_NONE/* Oscillator selection */
Config _ _ CONFIG3, WPEND_WPENDMEM/* Write protect Range selection */& WPCFG_WPCFGDIS/* Write protection Config page */& WPDIS_WPDIS/* Write protection */& WPFP_WPFP255/* Write Protection Flash page */
What can be the problem?
Thank you.